chrispeng [ad_1]
Product introduction:
1. Introduction
The elevator IC card management system can carry out computerized intelligent control and management of elevator passengers, effectively preventing idle people from using the elevator to enter and exit the building, thereby improving the safety management level of the building.
The elevator IC card management system adopts one person, one card, assigns authority, and takes the elevator with the card. The floors that each card can reach are designated by the property management department when the card is issued. The cardholder can call the elevator and stop at the desired floor without pressing buttons on the designated floor; it can neither call nor stop at the non-designated floor.
2. System structure and function
The elevator IC card management system includes elevator IC card, card reader and signal controller (instruction manager in elevator IC card), elevator IC card reader/writer (desktop). Allows the designated arrival floor signal to be stored in the IC card, and the system operates the IC card through the card reader; the card reader communicates with the IC card through radio frequency signals and provides energy to the chip on the IC card; the IC card responds The instructions of the card reader and report the results of the processing.
The card reader reads the information stored in the IC card and transmits it to the signal controller. The signal controller controls the elevator command board according to the received floor signal that is allowed to be opened or needs to be registered, and opens the corresponding command button or directly registers the corresponding Floor instructions.
The command manager in the elevator IC card itself contains the internal command signal control board and the card reader, and the internal command signal control board contains the stored calendar, clock, 485 interface, etc. It is a device installed on the elevator’s internal call board to receive and identify IC cards; and to control the elevator’s internal call buttons. Under certain conditions (such as elevator maintenance, fire alarm) the controller can also release the control of the buttons.
The desktop IC card reader/writer is a computer-based management system. It contains the elevator IC card software management system. The software itself has powerful database management. In addition to the above functions, it can also initialize the IC card (that is, make the blank card of the company), which is the IC card issued by the company. Perform identification and confirmation, and at the same time realize multiple functions such as recharging, counting, printing, customer data query and statistical management of IC cards.
3. Classification and functions of IC cards
1. Ordinary single-layer card
This card is used by ordinary elevator passengers. One person has one card. With the card, you can only reach the designated floor. When in use, when passengers enter the car, they bring the IC card close to the IC card manager, and the command manager in the elevator IC card will automatically recognize the legitimacy of the IC card. If the card is legal and the passenger does not need to press a button to select a floor, the system will automatically light up the call light of the floor you are going to and stop at the landing. If the card is illegal or there is no card, the passenger cannot press the call light to achieve the purpose of boarding the elevator with the card.
2. Ordinary multi-layer card
The card is used by special passengers, such as security guards, elevator maintenance personnel, building management personnel, and personnel who can reach multiple floors. When the cardholder takes the elevator, the IC card is close to the elevator IC card manager, and the passenger can press the call key of the floor to be reached. If the passenger presses the call key of the floor that is not specified in the IC card, the operation will be invalid (lights Not bright), in order to achieve the purpose of limiting the reach of the floor.
3. Management card
This card is used by elevator managers. When someone loses an IC card or an IC card is stolen, the original cardholder should immediately report the loss to the elevator management personnel. The elevator management personnel can use the management card to enter the reported IC card number as a prohibited card number into the management card, and then After the management card is close to the elevator IC card manager for 30 seconds, when the prohibited card number is used again, it will be regarded as an illegal card and will not be confirmed. When the IC card is lost and recovered, the banned card number in the management card will be eliminated to achieve the purpose of being able to be reused. Of course, elevator managers can also use this function to prohibit or restore IC cards of cardholders who violate regulations (such as arrears). The management card cannot be banned, so the management card cannot be lost.
Four, system function
Automatic floor selection: Passengers bring the IC card close to the card reader of the elevator call board. There is no need for passengers to call the elevator by pressing the button. The system will automatically determine the legitimacy of the card, automatically identify the card number and automatically select the floor you arrive at.
Multiple permissions settings: The system provides a variety of cards with different permissions to adapt to the use of different passengers.
Single-layer card: For general users, users do not need to press the button to automatically select the floor they go to.
Multi-layer card: used for special users (security guards, cleaners), and can open any designated floors.
Management card: used by the manager of the property community, through which the lost or illegal IC card can be banned/used.
Fire-fighting function: The system itself has a fire-fighting function. When a disaster such as a fire or an earthquake occurs inside the building, the system itself will automatically get out of control and return to the state of taking the elevator without a card.
Perfect punch card machine:
Desktop punch card machine: has a rich database system. In addition to the above functions, it can also perform customer data query, statistics, printing and other functions. The system interface is all Chinese, so you can use it yourself without training.
Strong versatility: It can be applied to elevators of various brands and models. It has been installed and used in elevators such as Toshiba, KONE, Mitsubishi, Hitachi, Thyssen, and Blind.
Alternative function
Billing function: every time the card is swiped, counting or billing is performed.
Networking function: The internal call IC card controllers of multiple elevators in the district or area are connected through the 485 bus, and connected to a host. In this way, the IC card controller can complete the stand-alone control function, but also through the network The card swiping information is transmitted to the host in real time. In the host record, you can query when and who swiped the card for each elevator to take the elevator. You can also update the information of any elevator IC card control or suspend/start the use of any floor through the network. Or suspend/start the use of any IC card.
Remote call function: When the elevator IC card is used, it will bring safety and inconvenience to visiting guests. For this reason, a remote automatic elevator calling function is added on the basis of the IC card. The operation method is as follows: After the visiting guests are confirmed by the host, the host does not need to go to the elevator door to greet them. They only need to press the remote call button at home, and the elevator will automatically open the corresponding floor buttons to the guests, and the guests only need to press the host corresponding The floor button can reach the host’s home, which facilitates visits and mutual visits, and improves the intelligence of the elevator.
Access control elevator linkage function: In order to make it easier for residents to take the elevator, reduce the number of card swipings, and save waiting time for elevators, we have added the access control elevator linkage function on the basis of the IC card. The method of operation: After the residents swipe the card at the access control card reader communicator on the first floor (or the basement floor), the elevator IC card management system automatically recognizes the IC card, and the unit door is opened and the elevator is automatically called to the first floor (or the basement floor). After the owner enters the elevator, the button of the floor where the owner goes will be automatically lit, and the owner will be delivered to the destination floor directly.
One card: The elevator IC card can share an IC card with other IC card equipment, such as access control, parking, consumption, etc.
[ad_2]
